This is a low-cost mobile robot kit that comes with everything you need to build your first mobile robot except the electronic parts. It gives you the freedom to choose your preferred microcontroller whether it is Arduino, Micro:bit or any platform you like. It is particularly suitable for educators or training centers who wish to conduct a mobile robot workshop to students.
Specification
2 wheels + motors mobile robot chasis
Comes with all accessories to make a mobile robot
Include 4xAA batteries holder
Chassis size: ~215mm x ~150mm
Wheel Diameter: 67mm
Castor Height: 34mm
Motor parameters:
Comes presoldered with Red and Black wire, length ~ 15cm (After 15th September 2019)
Bidirectional
Gear Ratio = 48:1
Speed with 66mm diameter wheel = 0.65 m/s at 7.2VDC
Recommended operating voltage: 5 - 10VDC
Noise level < 65dB
Current Consumption:
100mA each motor at 3V
100mA each motor at 5V
120mA each motor at 6V
Document:
Assembly Instruction
Packing List:
1 x Plexiglass panels
2 x DC gear motor(TT motor) + Mini Wheel
1 x Castor
1 x 4 X AA battery holder
1 x Rocker switch
2 x Black slotted disc
Mounting screws and accessories
Microcontroller: ATmega328P
Operating Voltage (logic level): 5V
Input Voltage (recommended): 7-12V (5V if bypassing the onboard voltage regulator)
Input Voltage (limits): 6-15V
Digital I/O Pins: 14 (6 with pwm)
Analog Inputs: 8
DC Current per I/O Pin: 40ma (max of 200ma across all pins)
Flash Memory: 32kb (2kb used by bootloader)
SRAM: 2kb
EEFROM: 1kb
Clock Speed: 16mhz
Dimensions 0.73" x 1.70"
UNO R3 ATMega328P USB Compatible Development Board is a microcontroller board based on the ATmega328. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analogue inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.This upgraded model is completely compatible with original Arduino UNO.
Microcontroller
ATmega328
Operating Voltage
5V
Input Voltage (recommended)
7-12V
Input Voltage (limits)
6-20V
Digital I/O Pins
14 (of which 6 provide PWM output)
Analog Input Pins
6
DC Current per I/O Pin
40 mA
DC Current for 3.3V Pin
50 mA
Flash Memory
32 KB (ATmega328) of which 0.5 KB used by bootloader
SRAM
2 KB (ATmega328)
EEPROM
1 KB (ATmega328)
Clock Speed
16 MHz
The Arduino UNO R4 WiFi combines the processing power and exciting new peripherals of the RA4M1 microcontroller from Renesas with the wireless connectivity power of the ESP32-S3 from Espressif. On top of this, the UNO R4 WiFi offers an on-board 12x8 LED matrix, Qwiic connector, VRTC, and OFF pin, covering all potential needs makers will have for their next project.
With the UNO R4 WiFi, you can easily upgrade your project and add wireless connectivity to expand the reach of your current setup. If this is your first project, this board has everything you need to spark your creativity.
Hardware compatibility with UNO form factor: The UNO R4 WiFi maintains the same form factor, pinout, and 5 V operating voltage as its predecessor, the UNO R3, ensuring a seamless transition for existing shields and projects.
Expanded memory and faster clock: The UNO R4 WiFi boasts increased memory and a faster clock speed, enabling more precise calculations and effortless handling of complex projects.
Extra on-board peripherals: The UNO R4 WiFi introduces a range of on-board peripherals, including a 12-bit DAC, CAN BUS, and OP AMP, providing expanded capabilities and design flexibility.
Extended 24 V tolerance: The UNO R4 WiFi supports a wider input voltage range, allowing seamless integration with motors, LED strips, and other actuators using a single power source.
HID support: With built-in HID support, the UNO R4 WiFi can simulate a mouse or keyboard when connected to a computer via USB, making it easy to send keystrokes and mouse movements.
Wi-Fi® and Bluetooth®: The UNO R4 WiFi hosts an ESP32-S3 module, enabling makers to add wireless connectivity to their projects. Combined with the Arduino IoT Cloud, makers can monitor and control their projects remotely.
Qwiic connector: The UNO R4 WiFi features a Qwiic I2C connector, allowing easy connection to nodes from the extensive Qwiic ecosystem. Adapter cables also enable compatibility with sensors and actuators based on other connectors.
Support for battery-powered RTC: The UNO R4 WiFi includes additional pins, including an "OFF" pin to turn off the board and a "VRTC" pin to keep the internal Real-Time Clock powered and running.
LED matrix: The UNO R4 WiFi incorporates a bright 12x8 red LED matrix, ideal for creative projects with animations or plotting sensor data, eliminating the need for additional hardware.
Diagnostics for runtime errors: The UNO R4 WiFi includes an error-catching mechanism that detects runtime crashes and provides detailed explanations and hints about the code line causing the crash.
MEFV22C is a BBC micro:bit CLUB contains 10x BBC micro:bit V2 boards and all essentials needed to power boards and start programming. This BBC micro:bit is a pocket-sized computer that introduces you to how SW and HW work together. It has an LED light display, buttons, sensors, a speaker, microphone and many other input/output features that, when programmed, let it interact with you and your world. You will need a computer, tablet or phone to write and send code to the micro:bit, but once the code is on the micro:bit it works as a standalone device with just the battery pack. Bluetooth 5.1 connectivity with Bluetooth Low Energy (BLE), ideal for communicating with other devices such as smartphones and tablets.
micro:bit works with Microsoft, MacOS, Apple iPads(and iPhones) and Android devices
Computing is made physical
Use the micro:bit to sense, measure and log light, temperature, sound, movement, magnetism
Nordic nRF52833 processor with 512KB flash and 128KB RAM
5x5 LED display matrix, 25 red LEDs with 255-step intensity control
2 programmable tactile button for user funct, full speed USB 2.0 interface via micro USB connection
New notched edge connector makes it easier to connect things like crocodile clip, conductive thread
MEMS Microphone with LED indicator, dedicated I2C bus for peripherals
Onboard speaker, capacitive touch sensor, motion sensor and temperature sensors
LED matrix can be used to sense ambient light with software algorithm
BitPlayer provides you inspiration and excitement to make creations such as a portablepiano or a smart calculator. To be easier to carry and use, BitPlayer abandoned an allbutton design that a typical game controller would use in favor of a 2-axes joystick. Itincludes another 6 programmable buttons labeled as L, R, A, B, C and D. Besides, theBitPlayer itself features a buzzer, a vibration motor and a Grove I2 C port to give kidslively and interactive experience of game. You can easily enjoy DIY projects anywhereby installing 2 AAA batteries into the BitPlayer. As tested already, BitPlayer can interactwith other devices when Bluetooth positioning is within a distance range about 10meter. If you want to implement a remote control car, we recommend that you alsoprepare
Compatibility: Raspberry Pi 3 B+, 3, 2 and B+
Color / Material: Transparent Smoked Polycarbonate
Port access: Audio / Composite, HDMI, USB, microUSB, microSD
Cable Pass-throughs: GPIO, CSi, DSi
HAT Compatibility: Remove top of enclosure for HAT access
Tools Required: Completely tool-less
Mounting: Screw key-holes on bottom
Camera Compatibility: Compatible with Raspberry Pi Camera V1 and V2 (standard and NOIR)
This transparent enclosure for the Raspberry Pi combines great looks and great features that anyone can afford. It is an economical enclosure for your Raspberry Pi which is made of strong, transparent polycarbonate material to keep your Pi safe and looking good. Your Pi snaps securely in place without the use of any tools. All ports can be easily accessed and there's even a GPIO cable pass-through for prototyping. The tool-less design also has provisions for the Raspberry Pi Camera which also snaps right into place and safely protected.
Feature
Note
For optimal performance with reComputer, we recommend using 128GB / 256GB / 512GB / 1TB SSDs from Seeed. Since some SSDs on the market may only be compatible with specific JetPack versions which may cause the device to fail to function properly, and this issue is also present with official NVIDIA dev kits.
If you are looking for the version without power adapter, please check out reComputer J2021 without power adapter.
Specification
Jetson Xavier NX System on Module
AI Performance
reComputer J2022, Xavier NX 16GB
reComputer J2021, Xavier NX 8GB
GPU
384-core NVIDIA Volta™ architecture GPU with 48 Tensor Cores
CPU
6-core NVIDIA Carmel Arm®v8.2 64-bit CPU 6MB L2 + 4MB L3
Memory
16 GB 128-bit LPDDR4x 59.7GB/s
8GB 128-bit LPDDR4x 59.7GB/s
Storage
16 GB eMMC 5.1
Video Encoder
2x 4K60 | 4x 4K30 | 10x 1080p60 | 22x 1080p30 (H.265)
Video Decoder
2x 8K30 | 6x 4K60 | 12x 4K30 | 22x 1080p60 | 44x 1080p30 (H.265)
Carrier Board
Networking
Ethernet
1x RJ45 Gigabit Ethernet Connector (10/100/1000)
M.2 KEY E
1x M.2 Key E
I/O
USB
4x USB 3.1 Type A Connector；
1x USB Type-C (Device mode)
CSI Camera
2x CSI Camera (15 pos, 1mm pitch, MIPI CSI-2 )
Display
1x HDMI Type A; 1x DP
Fan
1x FAN connector(5V PWM)
CAN
1x CAN
Multifunctional Port
1x 40-Pin Expansion header
RTC
RTC 2-pin
RTC socket
Power
9-19V DC
Mechanical
Dimensions (W x D x H)
130mm x 120mm x 58.5mm (with case)
Installation
Desk, wall-mounting
Operating Temperature
-10℃~60℃
Warranty
1 Year
Hardware Overview
reComputer J202 carrier board, included in the full system - reComputer J2021
Desktop, Wall Mount, Expandable, or Fit in Anywhere
Application
Autonomous Mobile Robot (AMR)
AI Video Analytics
Machine Vision
Documents
Datasheet
Schematic
3D File
Seeed Nvidia Jetson Product Catalog
Nvidia Jetson Comparison
Nvidia Jetson Product Comparison
Seeed Nvidia Jetson Success Cases
Seeed Jetson One Pager
ECCN/HTS
HSCODE
8471419000
USHSCODE
8543708800
UPC
EUHSCODE
8471800000
COO
CHINA
Part List
Acrylic Cover
1x
Aluminium Frame
1x
Jetson Xavier NX module
1x
Aluminum heatsink with fan
1x
Carrier board
1x
12V/5A(Barrel Jack 5.5/2.5mm) Power Adapter (Power cable not included)
1x
The micro:bit Drone:bit Kit has successfully combined micro:bit with drones, which has provided another possibility for students to create and explore in the sky. Through your operation, you can give it commands of hovering at a fixed altitude, flying from a waypoint, curvilinear flight, rolling in the sky, etc. even in the classrooms, get your first professional micro:bit Drone:bit Kit now!
Drone:bit BREAKTHROUGH—PROFESSIONAL GRADE
It is the first kind of drone equipped with optical flow locating in professional-grade which is able to hover indoors in a fixed point through programming in the world, with built-in optical flow sensors in high sensitivity and TOF sensors, they help to hover and locate in a more precise way. It is probably your first drone in professional grade that listen to your commands!
Drone:bit BREAKTHROUGH-FLYING SAFELY
The sealed propeller guards make sure your drone flies safely.
Drone:bit IN CLASSROOMS-AVAILABLE IN CLASSROOMS
Drone:bit could fly in the classrooms!
Drone:bit BREAKTHROUGH—CODE FOR MORE PROJECTS
Simple graphical and Python programming, available for complicated flying routines, flying gestures and rolling, etc., there are more possibilities waiting to be explored.
Drone:bit IN CLASSROOMS — FIND MORE IN WIKI
SPECIFICATION
product name
micro:bit Drone:bit Kit
Rated Voltage
3.7V
Battery Capacity
800mAh
Charging Voltage
5V
Charging Current
0.8A
Charging Port
Micro-USB
Power Protection
Over Charge/Discharge Protection
Propeller Guards
Support
LED
5 PCS (one for power indicator, four for status indicator)
Waypoints
Optical Flow
Fixing Altitude
Barometer + TOF
micro:bit Programming
Support
2.4G Remote Control Mode
Support
Flying Time
8min
Weight
509g
Flying Height
≤100m
ELECFREAKS BBC micro bit Starter Kit is designed for children who are beginning to learn the electric circuit and programming knowledge. Students can use these micro:bit basic DIY kits to create or complete more experiments, such as traffic lights, using photocell to control micro:bit screen or LED.
Smart home Kit is a product about smart home projects based on micro:bitwhich is developed by ELECFREAK. We selected executed components commonly used at home as the TMP36 temperature sensor, sound sensor, crash sensor, servo, and motor. You can build scenes like windowsill, wardrobe, and fish tank, create yourself a smart sweet home and program to intelligently drive them using micro:bit. The smart home is what makes life more practical and playing with it is what makes life more interesting.
Micro:bit Smart Home Kit: Sensor:bit breakout board
micro:bit Smart Home Kit: Exquisite Sensor (Not Include micro:bit and Battery)
Learn Coding through DIY Smart Home Projects
Multiple Remote Control Modes
Smart Home Kit supports multiple programming methods (Makecode/Python/Javascript)
Rich Learning Resources about Health Monitoring
With the ELECFREAKS WIKI, grasping the essential concepts of robotics programming is a breeze. Learn, practice, and then apply these skills in the real world!
Official Collected Coding Extension
The programming expansion package of Smart Home kit is officially collected in micro:bit.
Application
Auto Windows
Automatically detect noise level, the window will be closed when the noise threshold.
Voice-activated Lights
Voice-activated lights are controlled by voice, light and time delaying with sound sensor and light sensor.
Smart fan
Automatically detect temperature. The fan will automatically drive when the temperature is over the threshold and it will show the current temperature.
Packing List
Specs
The Coral USB Accelerator adds a Coral Edge TPU to your Linux, Mac, or Windows computer so you can accelerate your machine learning models. This page is your guide to get started.
All you need to do is download the Edge TPU runtime and PyCoral library. Then we'll show you how to run a TensorFlow Lite model on the Edge TPU.
To learn more about the hardware, see the USB Accelerator datasheet.
Requirements
A computer with one of the following operating systems:
Linux Debian 10, or a derivative thereof (such as Ubuntu 18.04), and a system architecture of either x86-64, Armv7 (32-bit), or Armv8 (64-bit) (includes support for Raspberry Pi 3 Model B+, Raspberry Pi 4, and Raspberry Pi Zero 2)
macOS 10.15 (Catalina) or 11 (Big Sur), with either MacPorts or Homebrew installed
Windows 10
One available USB port (for the best performance, use a USB 3.0 port)
Python 3.6 - 3.9
On top of that, we have provided you with detailed instructions on the use of Raspberry Pi and the use of each module, which including 8 lessons for module. Just click the LEARN tab to view this user manual. Also you can check the Vedio Guide here, which will tell you how to use this kit step by step.
All in all, whether you are a student, teacher, artist, hardware enthusiast, and so on, with the help of the Grove Base Kit for Raspberry Pi, you will get to know Raspberry Pi quickly and comprehensively.Part List
Grove Base Hat for Raspberry Pi
Grove - Red LED Button
Grove - Buzzer
Grove - Moisture Sensor
Grove - Temperature & Humidity Sensor (DHT11)
Grove - Light Sensor
Grove - mini PIR motion sensor
Grove - Ultrasonic Ranger
Grove - Relay
Grove - Servo
Grove - 16 x 2 LCD (White on Blue)
This is a low-cost expansion board for Micro:bit, which is specifically used for the IO ports of Micro:bit. It has taken all the IO resources on the Micro:bit, and also has a buzzer on the board. It is connected to the P0 pin through the jumper cap. The P0 pin can be released using a jumper cap. The small size is very suitable for small projects using Micro:bit.
Features
Small size, very suitable for DIY
All IO ports are extracted
On-board buzzer- you can directly use the music module in MakeCode to play music. At the same time, the 3.5mm audio connector on the board can be connected to audio equipment; such as, headphones to have more creative endeavors.
Two LEGO-compatible pin holes for easy assembly and integration
The 3PIN interface is distinguished by yellow, red, and black. It is created so that plugging it in the wrong way is difficult, and it is convenient to plug in the sensors.
It imitates the 5PIN gold fingers on the Micro:bit. This is convenient for makers who like to use the alligator clips.
Compared with IObit1.0, the biggest difference is that it can input and output 5V, support 5V sensor use, and increases the drive capacity (can drive multiple 9g small servos).
Includes 1A self-recovery fuse
Custom-designed silk screen board
Product parameters
Length x width x height: 57mmx44mmx12mm
Technical parameters
Power supply mode: IobitV.2.0 supports USB5V power supply. This power supply mode requires pressing the blue power switch.
Working voltage: 3V-5V (5V sensor module is not supported under 3V power supply)
Output current: 3V and 5V power interface with maximum output 1A
Serial port extraction: serial port can map IO port
I2C port leads: pins 19 and 20 can only be used as I2C function pins. They cannot be read and written as ordinary IO ports, because Micro:bit bottom is dead.
Spi port leads; 14, 15 (IO port can be read and written).
Programming:
MakeCode/KittenBlock (based on Scratch3.0) with hardware: Micro:bit.
Specifics:
It is consistent with Micro:bit programming, because IObit does not have its own drive chip (except buzzer). The building block that is generally used with IObit is to operate the IO port. Many sensors on the market return a high and low voltage. Flat, or an analog value. For actuators, the microbit needs to output high and low level to control. People who are not familiar with this aspect can search Netease Cloud Classroom: Xiaoyan Technology and find the arduino tutorial, which explains how to use the commonly used sensors on the market, the principle is the same.
With common building blocks -> pin
Before using the building blocks, you must first understand the control method or reading method of the electronic module you are using.
Digital reading
Most newbies will fall out of here because they often ignore setup pull-ups or pull-downs during initialization. So the level state will fail after reading it once. Therefore, we must pay attention to this. Micro:bit itself does not help to set up and down by default, you need to set it yourself.
Analog reading
In response to the analog reading, because the analog reading will return a value of 0-1023, it is always inconvenient to display it with a dot matrix screen. So here we take advantage of the unique serial port debugging function of the MakeCode offline version produced by Xiaoyan. First, download the program shown in the figure to open the serial port. In step 2, the console of the device will appear, you can see the data returned in real time.
Digital writing
Digital read here does not need to set up and down
Analog write
Simulated writing an example of a flashing light
The most commonly used IO port operation is one of these four types. After you master it, you should have no problem with the commonly used sensors on the market. Another thing to note is that the sensors on the market are 5v and 3.3V compatible. But some can only work in 5V. For example, the blue ultrasonic wave that Taobao sells can ordinarily only work in 5V. If IObit is connected, the number read back will always be 0, because the module is not working properly!
Introduction to IObit hardware:
5V power
Insert the USB power supply (5V 1A) as shown in Figure 1. Press the blue button at 2, and the red indicator light at 3 will light up. You can use the left 5V interface.
P0 buzzer
Toggle switch to turn off the buzzer function (see the silk screen on the back of the board for status)
3Pin IO port leads
All the pins in the Micro:bit have been taken out without any reservation (Note: there are no P17 and P18 on the Micro:bit, it’s not that the IObit is not taken out)
Yellow corresponds to the different IO pins
Red corresponds to 3.3V/5V (with silkscreen)
Black corresponds to GND
5PIN gold fingers
The gold fingers of the Micro:bit are used to draw 3v, gnd, P1, P2, and P3 respectively. This is for users who prefer to use alligator clips
40P Micro:bit horizontal socket
Compact size socket
Board mounting holes and fixing
The two outermost holes are approximately 4.8 mm in diameter and are compatible with Lego friction pins with a spacing of 48 mm.
3.5mm audio interface
You can plug in a 3.5mm jack audio device and play the sound of the P0 pin.
IObit programming use:
If you haven’t gotten started with Micro:bit, first get started with Micro:bit, this is the operating premise.
Use music blocks directly in MakeCode to CQ0056.png
P0 pin is
If you use P0, remember to turn the buzzer toggle switch off (because the buzzer is combined with P0)
When using the Micro:bit power supply, IObit IO port drive capability is very weak, IO port current is less than 200mA, please do not connect high current devices (such as large servo MG995, DC motor), otherwise it will burn out the Micro:bit , you must fully understand before using what the device current conditions needed
When using a 5V external power supply, you can drive multiple small servos, but please note that the maximum current is 1A!
If you use the high-low read function of the pin, you must set the pull-down on the pin.
If P0 is used as a normal IO port, the buzzer toggle switch must be turned off, otherwise the buzzer will sound or the IO read value will be abnormal.
Use the shared pin with the Micro:bit dot matrix (such as 3, 4, 5, 6, 7, 8, 9, 10, 11), remember to disable the dot matrix screen on the software, otherwise it will be a bit of a screen burst
Do not use IO19, 20. 19 and 20 cannot be used as an IO port. Although the display on the MakeCode software can be used, it is actually not used! It can only be used for I2C communication
The USB port allows a maximum input current of 1A.
Do not place it on a metal surface to avoid short circuit
Hardware Resources
5V external power input（with anti-reverse protection）
Power switch
Power Indicator
Battery Indicator
Micro USB charing port
4-channel DC motor / 2-channel stepper motor
Jumper for buzzer selection
8 channel IO（corresponding to Micro:bit P0-P2、P8、P12-P15）
5V and GND port
Buzzer
8 channel servo port
I2C interface (expandable I2C module)
18650 battery case
Bettery protection recovery push button
Micro:bit edge connector
4x RGB pixel
Servo driver (PCA9685)
2xDc/Stepper driver (DRV8833)
KittenBot robot chassis mounting hole
Standard LEGO hole
Version Comparison
The Official Raspberry Pi HDMI cable is the perfect accessory to compliment your new Raspberry Pi 4 Model B board. This is a micro HDMI to standard HDMI cable which is 1m long and available in black or white.The high-performance Raspberry Pi HDMI cable supports 3D, 4K, 2K, 17.8Gbps, 2160P/60Hz and X.V.colour.
Specification
2.4G NRF24L01 Wireless Transceiver/Receive Module โมดูลสื่อสารส่งข้อมูลไร้สาย NRF24L01 2.4GHz
NRF24L01 is a work in the 2.4-2.5GHz worldwide ISM band single-chip transceiver, wireless transceiver, including: the frequency generator the enhanced SchockBurstTM mode controller power amplifier crystal amplifier modulator demodulator output power channel selection and protocol set by the SPI interface to set a very low current consumption, lower current consumption mode 12.3mA Power-down mode and standby mode when in transmit mode emission power 6dBm when current consumption is 9.0mA acceptance model.
Ball to open ISM band maximum 0dBm transmit power, license-exempt use. The open 100 meters!
Support six channels of data reception
(1) low operating voltage: 1.9 ~~ 3.6V low-voltage
(2) high-rate: 2Mbps, air transmission time is very short, greatly reducing the wireless transmission of collision phenomena (software settings 1Mbps or 2Mbps air transmission rate)
Multi-frequency points: 125 frequency points, to meet the multi-point communications and frequency hopping communications needs
4 ultra-compact: built-in 2.4GHz antenna compact 15x29mm (including antenna)
(5) Low power consumption: when in answer mode communication, fast air transmission and start-up time greatly reduces the current consumption.
Low application cost: NRF24L01 integrates all RF protocol high-speed signal processing section, such as: automatically resend lost packets and automatically generate an acknowledge signal, etc. the nRF24L01 The SPI interface can take advantage of the microcontroller hardware SPI port or microcontroller I / O port to simulate the internal FIFO can be used with a variety of low-speed microprocessor interface, easy to use low-cost microcontroller.7 facilitate the development: the link layer is fully integrated in the module, very easy to develop. Automatic retransmission function, automatic detection and retransmission of lost packets, the retransmission time and the number of retransmission can be software-controlled automatic storage is not received the packet of the response signal auto-answer, after the receipt of a valid data, the module automatically sends the reply fixed frequency detection signals without any additional programming Carrier Detect - built-in hardware CRC error detection and point-to-multipoint communication address control packet transmission error counter and carrier detection can be used for frequency hopping set can also set up six to receive the channel address, can have a choice of open receive channel standard the pin Dip2.54MM spacing interfaces for embedded applications.
Feature
Note
The reComputer J3011 is equipped with the same NVIDIA Jetson Orin Nano 8GB production module. You can perform a self - upgrade to Jetpack 6.2. Once upgraded, you'll instantly experience a significant boost in computing power, with the performance leaping from 40 Tops to 67 Tops, offering capabilities comparable to those of the NVIDIA Jetson Orin Nano Super Developer Kit.
For optimal performance with reComputer, we recommend using 128GB / 256GB / 512GB / 1TB SSDs from Seeed. Since some SSDs on the market may only be compatible with specific JetPack versions which may cause the device to fail to function properly, and this issue is also present with official NVIDIA dev kits.
If you are looking for the version without power adapter, please check out reComputer J3011 without power adapter
reComputer J3011 (original with JP5.1.3)
reComputer J3011 (super with JP6.2)
GPU
NVIDIA Ampere architecture
1,024 CUDA Cores
32 Tensor Cores
635 MHz
NVIDIA Ampere
architecture
1,024 CUDA Cores
32 Tensor Cores
1,020MHz
AI PERF
40 INT8 TOPS (Sparse)
20 INT8 TOPS (Dense)
67 TOPS (Sparse)
33 TOPS (Dense)
CPU
6-core Arm Cortex-
A78AE v8.264-bit CPU
1.5 GHz
6-core Arm Cortex-
A78AE v8.264-bit CPU
1.7 GHz
Memory
8GB 128-bit LPDDR5
68GB/s
8GB 128-bit LPDDR5
102GB/s
MODULE POWER
7W|15W
10W|15W|25W
Specification
Jetson Orin Nano System on Module
AI Performance
reComputer J3011 - Orin Nano 8GB, up to 67 TOPS
reComputer J3010- Orin Nano 4GB – up to 34 TOPS
GPU
1024-core NVIDIA Ampere architecture GPU with 32 Tensor Cores (Orin Nano 8GB)
512-core NVIDIA Ampere architecture GPU with 16 Tensor Cores (Orin Nano 4GB)
CPU
6-core Arm® Cortex®-A78AE v8.2 64-bit CPU 1.5MB L2 + 4MB L3
Memory
8GB 128-bit LPDDR5 68 GB/s (Orin Nano 8GB)
4GB 64-bit LPDDR5 34 GB/s (Orin Nano 4GB)
Video Encoder
1080p30 supported by 1-2 CPU cores
Video Decoder
1x 4K60 (H.265) | 2x 4K30 (H.265) | 5x 1080p60 (H.265) | 11x 1080p30 (H.265)
Carrier Board
Storage
1x M.2 Key M PCIe (M.2 NVMe 2280 SSD 128G included)
Networking
Ethernet
1x RJ-45 Gigabit Ethernet (10/100/1000M)
M.2 KEY E
1x M.2 Key E(pre-installed 1x Wi-Fi/Bluetooth combo module)
I/O
USB
4x USB 3.2 Type-A (10Gbps), 1x USB2.0 Type-C (Device Mode)
Camera
2x CSI (2-lane 15pin)
Display
1x HDMI 2.1
Fan
1x 4 pin Fan Connector (5V PWM)
CAN
1x CAN
Multifunctional Port
1x 40-Pin Expansion header
1x 12-Pin Control and UART header
RTC
1x RTC 2-pin, supports CR1220 but not included
Power
9-19V DC
Mechanical
Dimensions (W x D x H)
130mm x 120mm x 58.5mm (with case)
Installation
Desk, wall-mounting
Operating Temperature
-10℃~60℃
Warranty
1 Year
Hardware Overview
reComputer J401 carrier board, included in the full system - reComputer J3011
● Desktop, Wall Mount, Expandable, or Fit in Anywhere
Application
Application Fields:
AI Video Analytics
Machine Vision
Autonomous Mobile Robot (AMR)
Generative AI
● Capable of Bringing Generatie AI to the Edge
Now you can build AI agents capable of processing large amounts of live or archived videos and images with Vision-Language Models (VLM) such as LLaVA, this new AI agents help nearly every industry summarize, search, and extract actionable insights from video using natural language.
● Build Multi-streams AI Video Analytics
For building video analytics, Jetson Orin Nano incorporates the NVIDIA Multi-Standard Video Decoder. This video decoder accelerates video decode, supporting low resolution mobile content, Standard Definition (SD), High Definition (HD) and UltraHD (8K, 4K, etc.) reComputer J3011 can take 13x1080p30 streams. See our tested YOLOv8 performance using NVIDIA Deepstream of single model and multi model on multi streams.
● Fastest Way to Deploy Generative AI and Computer Vision Models
We have jetson-example prepared for you! It offers one-line deploy projects edge AI applications of generative AI including Ollama, Llama3; computer vision including YOLOv8; and others. We have configured all environment for you to provides single command deployment of projects.
โปรเจกต์นี้เป็นตัวอย่างของการใช้งาน Large Language Models (LLMs) บน Raspberry Pi 5 อุปกรณ์ขนาดเล็ก แต่ทรงพลังอย่างมากในการพัฒนา และความสามารถของ Raspberry Pi 5 นั้นเพิ่มขึ้นอย่างมหาศาลจากรุ่นก่อน ทำให้สามารถรองรับการประมวลผล AI และการเรียนรู้ของเครื่องได้ดียิ่งขึ้น ในโปรเจกต์นี้เราจะพัฒนาและปรับแต่ง LLMs ให้เหมาะสมกับฮาร์ดแวร์เล็กๆ แต่ทรงพลังนี้ เปิดโอกาสใหม่ให้กับการประมวลผลภาษาธรรมชาติ (NLP) ในระดับที่ประหยัดพลังงานและราคาประหยัด เหมาะสำหรับนักพัฒนาที่ต้องการทดสอบและประยุกต์ใช้งาน AI ได้ทุกที่ทุกเวลา
รหัส
สินค้า
NF68465
SD Card 32GB
NF78136
Raspberry pi 5 Active Cooler
F89045
Raspberry pi 5 4GB
F91476
Raspberry pi AI Kit
F74148
micro hdmi to hdmi
F92988
Raspberry pi 5 Adapter
F89048
Raspberry pi 5 Case
NF73397
Flash Drive 128 GB
โปรเจกต์นี้จะพาคุณเข้าสู่โลกของการรู้จักอักษรด้วยเทคโนโลยี OCR (Optical Character Recognition) บน Raspberry Pi 5 รุ่น 8GB พร้อม AI Kit ที่ทรงพลัง เหมาะสำหรับการแปลงภาพถ่ายเอกสารให้เป็นข้อความ Digital ได้อย่างรวดเร็วและแม่นยำ Raspberry Pi 5 มีประสิทธิภาพสูงเพียงพอในการประมวลผล AI ทำให้ OCR เป็นไปได้ในอุปกรณ์ขนาดเล็กแต่ทรงพลังนี้ โปรเจกต์นี้เหมาะสำหรับผู้ที่ต้องการแปลงข้อมูลกระดาษเป็น Digital อัตโนมัติในงบประมาณที่จับต้องได้ พร้อมแนะนำวิธีการติดตั้งและการใช้งานอย่างครบครัน
รหัส
สินค้า
NF68465
SD Card 32GB
NF78136
Raspberry pi 5 Active Cooler
F89046
Raspberry pi 5 8GB
F91476
Raspberry pi AI Kit
F74148
micro hdmi to hdmi
F92988
Raspberry pi 5 Adapter
F89048
Raspberry pi 5 Case
F91830
Raspberry pi Camera
F91747
FPC Camera Cable
โปรเจกต์นี้จะสร้างระบบสแกนบาร์โค้ดด้วย Raspberry Pi ที่ไม่เพียงแค่สแกนบาร์โค้ด แต่ยังบันทึกวิดีโอของการสแกนลงใน USB โดยอัตโนมัติ
รหัส
สินค้า
NF68465
SD Card 32GB
NF65047
Heat Sink for pi3,pi4,Opi
F80094
Raspberry pi 4 4GB
F74148
micro hdmi to hdmi
NF73987
Adapter Raspberry pi 4
F74138
Raspberry pi 4 Case
NF73407
เครื่องอ่าน Barcode
NF73397
Flash Drive 128 GB
NF91746
Raspberry pi Camera
โปรเจกต์นี้นำเสนอการสร้าง Smart AI Speaker ด้วย Mycroft บน Raspberry Pi ที่ผสานความสามารถผู้ช่วยเสียงอัจฉริยะเข้ากับความยืดหยุ่นของอุปกรณ์ขนาดเล็ก แต่ทรงพลัง Raspberry Pi สามารถประมวลผลการสั่งงานด้วยเสียงได้อย่างรวดเร็ว พร้อมให้ประสบการณ์ใช้งานที่ราบรื่นและเป็นส่วนตัว เราจะสอนคุณตั้งแต่การติดตั้ง จนถึงการปรับแต่ง Mycroft ให้ตอบสนองได้ตามต้องการ ทำให้คุณสามารถสร้างผู้ช่วยอัจฉริยะที่เข้ากับบ้านของคุณได้อย่างสมบูรณ์แบบ ราคาประหยัด ติดตั้งง่าย และปรับแต่งได้ตามใจ!
รหัส
สินค้า
NF68465
SD Card 32GB
NF78136
Raspberry pi 5 Active Cooler
F89045
Raspberry pi 5 4GB
F74148
micro hdmi to hdmi
F92988
Raspberry pi 5 Adapter
F89048
Raspberry pi 5 Case
Mic USB
Speaker USB 3.5mm. Jack
Due to the product taking longer than usual to arrive.
Please inquire about the product every time before making payment. Thank you very much.
The Raspberry Pi 3 Model B+ is the latest addition to the Raspberry Pi 3 family, featuring a 64-bit quad core processor running at 1.4GHz, dual-band 2.4GHz WiFi 2.4/5GHz, Bluetooth 4.2/BLE, and PoE capability (via a separate PoE HAT add-on).
details
Broadcom BCM2837B0, Cortex-A53, 64-bit, Quad-core SoC at 1.4GHz
1GB LPDDR2 SDRAM
2.4GHz / 5GHz IEEE 802.11 b / g / n / ac Wireless LAN (WLAN)
Bluetooth Low Energy v4.2 (BLE)
Gigabit Ethernet via USB 2.0 (Max speed 300Mbps)
4 x USB 2.0 ports
GPIO 40 pin
Full Size HDMI, MIPI DSI display port, MIPI CSI camera port
4-pole stereo audio/composite video output port
MicroSD card slot for operating system and storage
Enable Power over Ethernet (PoE) (requires separate PoE HAT)
Power supply requirements - 5V/2.5A DC via micro USB or GPIO
Raspbian operating system
The Raspberry Pi 3 Model B+ is the latest product in the Raspberry Pi 3 range, boasting a 64-bit quad core processor running at 1.4GHz, dual-band 2.4GHz and 5GHz wireless LAN, Bluetooth 4.2/BLE, faster Ethernet, and PoE. capability via a separate PoE HAT. The dual-band wireless LAN comes with modular compliance certification, allowing the board to be designed into end products with significantly reduced wireless LAN compliance testing, improving both cost and time to market. The Raspberry Pi 3 Model B+ maintains the same mechanical footprint as both the Raspberry Pi 2 Model B and the Raspberry Pi 3 Model B.
Broadcom BCM2837B0, Cortex-A53, 64-bit, quad-core SoC @ 1.4GHz
1GB LPDDR2 SDRAM
2.4GHz/5GHz IEEE 802.11 b/g/n/ac Wireless LAN (WLAN)
Bluetooth Low Energy v4.2 (BLE)
Gigabit Ethernet over USB 2.0 (maximum throughput 300Mbps)
4 x USB 2.0 Ports
Extended 40-pin GPIO Header
Full Size HDMI, MIPI DSI display port, MIPI CSI camera port
4-pole stereo audio/composite video output port
MicroSD card slot for operating system and data storage
Power over Ethernet (PoE) enabled (requires separate PoE HAT)
Power supply requirements - 5V/2.5A DC via micro USB or GPIO
